Name: KXK Dynamics XP Punch Kit V2
Brand: KXK Dynamics
SKU: KXK Dynamics XP Punch Kit V2
Price: 219.99 USD
Availability: InStock
Rating: 5.0 (1 reviews)

KXK Dynamics XP Punch Kit V2

$249.99 $219.99

This is a stout piece of hardware - intended for experienced detailers. Intended to be use with the KXK Dynamics/Oberk KO-1 Microfiber Sheet.

KXK Dynamics XP Punch Kit V2 features shorter punches with a brilliantly designed and extremely versatile punch handle! This over engineered tool is designed to take the brunt force when punching out 1-3/8", 2", and 2-3/4" pads in minutes. The Stryker handle allowed them to save material (providing increased savings to you) by shortening the punch portion of the unit and transferring the function of the handle into a single versatile peice which can be used on all 3 punches.

The XP-1 is capable of easily punching (15) 1" pads from a 6" in only a couple minutes. In other words... for every pad you turn into "swiss cheese" to create your 15 new pads you save $50! The XP-2 punches out (7) 2" pads for an impressive $25 savings per while the XP-3 can easily create (3) pads while still leaving room for (3) 1" pads to use excess.

Machines ideal for small pads

1-3/8" and 2" pads produced by the XP-1 and XP-2 are perfectly sized for your iBrid nano, LD-30, TA-50, and a variety of other machines on the market.

2-3/4" pads produced by the XP-3 will fit any 2 1/2" to 2 3/4" backing plate. The founders of KXK Dynamics use RUPES line of incredible machines day in and day out.... so for your "RUPES Mini" backing plate they came up with an ingenious solution... Punch it!

Why a 2-3/4" pad vs a 3" pad for the XP-3?

The XP-3 Pad Punch's diameter is slightly smaller than standard 3 inch backing plate diameters, and you may ask why. And the answer to you is: a higher pad yield, AKA more pads punched out of a 6" microfiber pad. But have no fear, it is a very simple backing plate modification that can be accomplished with, you guess it, the XP-3 Pad Punch. For most 3" backing plates, the XP-3 Pad Punch can be used to "trim" a slight ring off the edge of the plate to match the pads you will punch.

For those of you that do not use 1", 2", or 3" pads very often this kit is not a necessity... However for those who utilize 1", 2", and 3" pads, the KXK Punch Kit is a no brainer!

Kit Includes:

(1) XP-5 V2 Stryker Handle
(1) XP-1 V2 Pad Punch w/ blade cap
(1) XP-2 V2 Pad Punch w/ blade cap
(1) XP-3 V2 Pad Punch w/ blade cap
(1) Punch Board

Specifications

XP-1 Handle Styker:

XP-S Stryker Height: 4 1/2"
XP-S Stryker Diameter: 1 3/4"
XP-S Stryker Weight: 1.05 lbs

XP-1 Punch:

XP-1 Height: 2 1/2"
XP-1 Outer Diameter: 1 5/8"
XP-1 Weight: 0.70 lbs
Produces: 1-3/8" Dia. Pads

XP-2 Punch:

XP-2 Height: 2 1/2"
XP-2 Outer Diameter: 2 3/8"
XP-2 Weight: 1.20 lbs
Produces: 2" Dia. Pads

XP-3 Punch:

XP-3 Height: 2 1/2"
XP-3 Outer Diameter: 3 1/8"
XP-3 Weight: 1.55 lbs
Produces: 2-3/4" Dia. Pads

XP-0 Punch Board:

HPDE Plastic
Length: 10"
Width 8"

What should do if I see haze or micromarring after using the 2 step system.
Micromarring is common on the initial step. Repolish the area using the same combination to ensure that the polish was cycled and completely broken down, or the surface itself polished long enough. Typically, if you have any issues with the red pad and polish combination finishing, the firmer pad will normally resolve these issues on your specific paint work

What do I use for one step polishing?
We recommend our Yellow medium polishing pad paired with either out OBERK cut or OBERK polish depending on paint. Typically, we recommend harder paints – Oberk Cut with Yellow pad. Softer Paints – Oberk Polish with Yellow pad.

Note – A simple test spot with each combination above should easily determine which is better for your vehicle.

Customer Reviews

View all 1 review Write a review

KO-1 Microfiber Sheet Cutting Punch Pad Backside

KO-1 Microfiber Sheet 10x12

$64.00 $40.00

10 x 12" Microfiber Cutting Sheet
Designed for you to 'punch' out your desired size of pad
Smaller pads are ideal for compounding difficult small areas like bumper edges, mirrors, grill areas, A/B pillars, interior plastics
Punch up to (53x) 1.25" pads ($265 value)
Ideally would be used with the KXK XP Pad Punch Kit V2
Manufactured to our Oberk Microfiber cutting pad specification

We think paying $5+ for a 1.375" cutting pad is insanity. Time to stick it to the man. No one offered a better solution until KXK Dynamics brought their pad punch kit to market, giving the ability to punch out smaller pads of your size choice from larger pads in a cost conscious manner.

This is that concept, on steroids. In partnership with KXK Dynamics, we developed the KO-1, a 10 x 12" cutting sheet based on our #1 selling product, Oberk Microfiber Cutting Pad. Ideal to punch out 1.25, 2.0, or 2.625" pads for those hard to reach places when compounding a vehicle.

Punching this sheet vs purchasing individual pads:

1.25" Pads (53 punched) avg cost 0.75/ea pad vs $5/ea individual pad ($238 savings on one sheet punch)

What should do if I see haze or micromarring after using the 2 step system.
Micromarring is common on the initial step. Repolish the area using the same combination to ensure that the polish was cycled and completely broken down, or the surface itself polished long enough. Typically, if you have any issues with the red pad and polish combination finishing, the firmer pad will normally resolve these issues on your specific paint work

What do I use for one step polishing?
We recommend our Yellow medium polishing pad paired with either out OBERK cut or OBERK polish depending on paint. Typically, we recommend harder paints – Oberk Cut with Yellow pad. Softer Paints – Oberk Polish with Yellow pad.

Note – A simple test spot with each combination above should easily determine which is better for your vehicle.

Customer Reviews

View all 2 reviews Write a review

Oberk Vinyl Banner (Series v.2)

$99.99 $65.00

(Series v.2) Limited time product availability. Version.2 - the black edition is a big banner. We spent years figuring out our compounds and pads, but after a rigorous vinyl banner quality check we finally got the print quality we desired. This was a common request we heard from customers, so here it is!

Specifications:

72 x 30" Premium Indoor Vinyl Banner
10 mounting holes
Comes with no mounting hardware standard. If you want we can include (4) tapcon hardware/anchors and (4) fender washers for an additional $5. Tapcon hardware can be used into wood, plaster, drywall (no stud required), brick and concrete.

What should do if I see haze or micromarring after using the 2 step system.
Micromarring is common on the initial step. Repolish the area using the same combination to ensure that the polish was cycled and completely broken down, or the surface itself polished long enough. Typically, if you have any issues with the red pad and polish combination finishing, the firmer pad will normally resolve these issues on your specific paint work

What do I use for one step polishing?
We recommend our Yellow medium polishing pad paired with either out OBERK cut or OBERK polish depending on paint. Typically, we recommend harder paints – Oberk Cut with Yellow pad. Softer Paints – Oberk Polish with Yellow pad.

Note – A simple test spot with each combination above should easily determine which is better for your vehicle.

Customer Reviews

View all 1 review Write a review

KXK Dynamics R.I.D. Stix

$26.99 $19.99

The Worlds Smallest Production Sanding Blocks

The KXK Dynamics R.I.D. STIX advanced sanding blocks are designed to aid in the removal of random isolated deeper scratches that cannot be achieved by compounding and polishing alone. When used in combination with sand paper, R.I.D.STIX ergonomic, patent-pending design, maximizes the contact between the sanding block and a vehicle panel to obtain a more consistent, even sanding mark that can be polished out quickly and easily!

R.I.D. STIX are a much smaller companion piece to their big brothers, PALM BLOX.

Contains

• 2 Soft Foam Black Blocks
• 2 Hard Foam White Blocks

Specifications

• Contours To Surface
• Beveled Top
• No Bevel On Bottom
• Customizable
• MADE IN THE USA

What should do if I see haze or micromarring after using the 2 step system.
Micromarring is common on the initial step. Repolish the area using the same combination to ensure that the polish was cycled and completely broken down, or the surface itself polished long enough. Typically, if you have any issues with the red pad and polish combination finishing, the firmer pad will normally resolve these issues on your specific paint work

What do I use for one step polishing?
We recommend our Yellow medium polishing pad paired with either out OBERK cut or OBERK polish depending on paint. Typically, we recommend harder paints – Oberk Cut with Yellow pad. Softer Paints – Oberk Polish with Yellow pad.

Note – A simple test spot with each combination above should easily determine which is better for your vehicle.

Customer Reviews

View all 1 review Write a review

PR-2 Polishing Rack Gunmetal

$69.99 $59.99

Introducing the Hammered Gunmetal KXK Dynamics PR-2, designed for maximum mobility and efficiency! KXK Dynamics changed the detailing world with the markets first polishing rack designed for storing and displaying the detailers tools of choice... their polishers!

The PR-2 easily mounts to the wall or even directly to your detail cart! What's more, it is designed as an integrated shock absorber so that when placing the machine on the rack it does not fall off even if moving or bumped!

The KXK PR-2 can safely house up to 2 machines, one large in the front, and one mini unit in its rear cradle. Fabricated from high strength steel, the PR-2 is precision cut, punched, and formed to exact specifications. The PR-2 is coated in a high strength matte powder coat finish, both inside and out, to provide an additional layer of protection from oxidation and offer an industrial aesthetically pleasing finish.

Features

• Can be mounted onto a cart or wall
• Hammered Gunmetal Finish
• Easily fits a variety of dual action, pneumatic, and rotary buffers
• Keeps your machines organized
• Stores up to 2 machines
• Durable and rust-proof finish
• Neoprene gasket for hanging area is included

Specifications

• Material: 14 Gauge high strength steel
• Mounting hardware not included
• Finish: Industrial strength powder coat
• Width: 6”
• Height: 9”
• Depth from wall: 3"
• Weight: 1.9 lbs +/-
• Fastener spacing: 3/4” o.c.
• Storage opening: 5” x 6”

What should do if I see haze or micromarring after using the 2 step system.
Micromarring is common on the initial step. Repolish the area using the same combination to ensure that the polish was cycled and completely broken down, or the surface itself polished long enough. Typically, if you have any issues with the red pad and polish combination finishing, the firmer pad will normally resolve these issues on your specific paint work

What do I use for one step polishing?
We recommend our Yellow medium polishing pad paired with either out OBERK cut or OBERK polish depending on paint. Typically, we recommend harder paints – Oberk Cut with Yellow pad. Softer Paints – Oberk Polish with Yellow pad.

Note – A simple test spot with each combination above should easily determine which is better for your vehicle.

Customer Reviews

View all 2 reviews Write a review

Mountable Pad Hangers

$19.99 $13.99

New Product Release!

Oberk Car Care mountable pad hangers are a manufactured circular hook that can 'grab' the velcro/loop backing of any pad, up to 8" in size. We spent over 6 months making sure our mounts do not deteriorate or begin to lose their 'grab and we are happy to release this product to the public.

Perfect for a stylish or handy mounting to a cart, wall, wood board, or cabinet. Any material such as wood, metal, plastic, drywall that can accept a self-tapping screw, glue or a 3m command strip can be your new pad mount. The options are endless.

Although not included, our mountable pad hangers can be mounted via:

Glue
Self-tapping screw
3M Command strip, for a damage free option

What should do if I see haze or micromarring after using the 2 step system.
Micromarring is common on the initial step. Repolish the area using the same combination to ensure that the polish was cycled and completely broken down, or the surface itself polished long enough. Typically, if you have any issues with the red pad and polish combination finishing, the firmer pad will normally resolve these issues on your specific paint work

What do I use for one step polishing?
We recommend our Yellow medium polishing pad paired with either out OBERK cut or OBERK polish depending on paint. Typically, we recommend harder paints – Oberk Cut with Yellow pad. Softer Paints – Oberk Polish with Yellow pad.

Note – A simple test spot with each combination above should easily determine which is better for your vehicle.

Customer Reviews

View all 7 reviews Write a review